Product review: PowerGen Dual Port USB 2.1A 10W AC Travel Wall Charger with Nexus 7 Tablet, Samsung Galaxy 7.7 Tablet, and Samsung Galaxy Nexus cell phone, and SanDisk Sansa Clip+ player

I tested PowerGen Dual Port USB 2.1A 10W AC Travel Wall Charger with Nexus 7 Tablet, Samsung Galaxy 7.7 Tablet, and Samsung Galaxy Nexus cell phone, and SanDisk Sansa Clip+ player.
I received PowerGen wall and car chargers for testing from the manufacturer to write an honest and unbiased review and you will find both pluses and minuses of my experience in this review.

I am attaching a collage of 5 photos labeled with numbers 1 through 5 that I will be referencing in this review.

The first thing I noticed that this wall charger is fairly small, it takes up only one slot on the extension cord. Photos #1 and #4 show this plug on two different power strips.

The plug has two ports labeled "A" and "NA" which stands for Apple and Non-Apple devices. I own all Android devices but I tested both ports to see their behavior with my devices. The charger comes without a USB cord, so tested it with the USB cords that came with my devices.

I used Battery App to determine how each device recognized the external battery pack. 'AC' status means the charging is at full charging rate. 'USB' status indicates charging at a lower charging rate. 'Discharging' status means that the charging rate is below the power that the device is consuming so it slows down the discharge rate but does not re-charge.

The key findings:
(1) Samsung Galaxy 7.7 cannot be charged with this wall charger with either port
(2) "A" port provides reduced power for some non-Apple devices and does not work for others
*** Update 1/9/2013 ***
I repeated the test with Nexus 7 running Jelly Bean 4.21 and both ports are now charging it at AC rate.  The original test which showed poor performance on Apple port was Nexus 7 running Jelly Bean 4.1.
I also retested Galaxy Nexus Phone running CyanogenMod 10.1 version of Jelly Bean 4.21, but it showed no improvement. It still gets only USB charging rate on Apple port.

The table below summarizes my findings:

Nexus 7 Tablet (photo #4 and #5, note that the left port is labeled "A" and the right port is labeled "NA")
--------------
A port  -- discharging (Nexus 7 running Jelly Bean 4.1.)
A port  -- AC (Nexus 7 running Jelly Bean 4.21)
NA port  -- AC
Samsung Galaxy Nexus Phone
--------------------------
A port -- USB
NA port -- AC

Samsung Galaxy Tablet 7.7
--------------------------
A port -- discharging
NA port -- discharging

SanDisk Sansa Clip+ MP3 Player
------------------------------
A port -- charged at USB rate
NA port -- charged at AC rate

The behavior with Nexus devices was consistent and good on "NA" port. Samsung Galaxy Nexus Phone gets USB rate on Apple "A" port.  After upgrade to Jelly Bean 4.21 Nexus 7 gets AC rate on both ports.

Samsung Galaxy Tablet 7.7 did not work (was discharging) in both ports.

The MP3 player worked in both ports, but as USB rate in "A" port and at "AC" rate in in "NA" port. When I charge Sansa MP3 with a standard AC charger (photo #3), the MP3 player goes into charging mode, displaying the charging animated icon, the MP3 content is not played. When MP3 was plugged into the PowerGen plug (photo #3) it continued to play the content. I listen to books on my MP3 player so this caused me to move forward in my book and I had to manually reset my position by a few chapters to get back to where I was when I started charging. The positive side of this, is that is possible to continue listening while MP3 is recharging.

To summarize:

I liked:
---------
1. Good behavior with Nexus devices.
2. Solution for MP3 player with built-in battery
3. Can charge two devices (but one at a reduced rate for non-Apple devices)

I did not like:
--------------
1. Did not work with for my Samsung Galaxy tablet
2. For non-Apple devices one port has less power or does not work
3. For non-Apple devices the less useful plug takes up a little extra room

You can find it on Amazon by following this link.


Ali Julia review ★★★★☆